• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane can be an issue. This can be an opportunity to upgrade your windows to energy efficient or insulated ones to enjoy benefits such as improved comfort, higher resale value and reduced utility costs.

This is a project you could tackle yourself at only a fraction of the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

If your single-pane windows are outdated broken, deteriorating or damaged replacing them with more modern glass that is tempered or insulated will increase energy efficiency and decrease noise while maintaining the original character of older homes. The majority of homeowners with basic hand tools can repair windows with ease. You'll also require an additional window pane, glazier's tips, pliers, and latex glazing putty. If needed you can use a heatgun to warm the old putty. Before starting, wear gloves and safety goggles as working with broken glass may cause injuries.

Begin by removing any broken pieces of glass. It is best to use pliers for this however a flathead could be used equally. Use a wood chisel, nearest or putty knives to remove any old putty remaining around the frame and the window sash. Take your time and work slowly, taking care not to break the current replacement upvc window handles sash. This can be done best on an elevated ladder, not on the ground. Also, you should have someone below the sash hold it steady.

Make sure that the window frame is ready to receive the new pane once you have removed the old glue. Find the width and the height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to the nearest hardware store or home center and get a piece of stock glass cut to size. You can also cut the glass yourself if have the right tools.

After installing the glass After installing the glass, apply a small amount of caulking on the edges. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they create friction between the sash and frame but they should not be too loose.

Before applying the putty to the surface, knead thoroughly until it becomes soft and free from lumps. Then make it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to another, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of steel that allow glass to be secured to the frame without causing damage to the delicate surface. Knowing how to use these little helpers is easy and could save you money on professional installation or the cost of purchasing new glass.

Once the old putty and the glazier's point are gone Clean the frame thoroughly using a utility knife to eliminate any remaining residue. If necessary it is necessary to lightly sand the wood along the grooves of the rabbets to smooth rough areas. If you sand wood cover it with painter's tape to prevent accidental damage.

Take measurements of the empty frame and record precise measurements. Bring these measurements to a hardware store or home center and request that the new pane cut slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane into the frame and push firmly with your hands. Then use the point of your chisel or back end of the putty knife to make a tap on the glazier's points, as illustrated in Figure 11. The glazier's points should be aligned with the top edge of your pane and the shoulders should be just beneath that lip.

Apply a thin layer glazing compound to the rabbet grooves and edges of the new glass. This will protect and seal the edges. Allow it to dry and cure completely.

Install the new window sash when the glazing compound has dried. The first step is to coat the wood with a heavy coat of linseed oil. This will prevent the new putty from sucking in the moisture and deteriorating and cracking over time. Apply this coat using a brush or the tip of your putty knife, then use the chisel, or the back end of the putty knife to gently hammer in the new sash and glazier's tips into the rabbet grooves. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball thrown or a rock thrown by error, or a tree falling can result in a cracked or cracked window. Fortunately, the majority of windows can be replaced by simply putting a new piece in place. The glass is held in place by small clips made of metal called the glazier's pointed and putty, also called glazing compound. Remove the old pane and clean the area with a rag, a pull-type scraper or wood chisel. Wear protective glasses and gloves while doing this work. You'll require a heat gun when the window is fixed to the frame.

If you are planning to replace the original sash, remove any molding pieces that are used to secure the old pane. Sand the sash until it is flat and ready for new caulk. Once the sash is re-installed then, apply a new silicone caulk around the glass to ensure that it won't leak or discolor as time passes.

Remove the glazing points from the rabbets. These are the grooves in the sash, where the glass is. If they're difficult to cut out, try placing the hand tool, such as a heat gun over them to soften them up first. If you're using a heat gun, make sure not to damage the railings of the sash or the sash itself by using the tool too tightly.

Prepare the bed for your new pane after you have removed the old glaze and putty. Roll a rope of glazing compound between your fingers and then make it about 1/2 inch thick. Press it into the rabbets, where the glass will be put. It's important that the glass is positioned against the putty on each side So if you have to tap it, gently press the glass into the rabbet with your thumb.

If the new pane is cracked then you can seal it with a solvent-based glue or silicone caulk prior pressing it into the sash. If not, you'll have to apply putty on the crack to form an impervious seal to keep water out. After the putty has dried clean the oily film off the glass and allow it to dry completely before painting. Paint after the putty is completely dry. It won't create a solid seal and may be leaking or discoloring over time.

Paint

If you've experienced a broken window pane, you might be worried about the expense of replacing it. However, replacing a single glass pane doesn't have to break the bank if you do it yourself. In fact windows with double panes can be replaced for only a fraction of the cost of an expert.

If you are working on a large-sized window, make sure that it is securely attached to the frame. By using the correct tools and techniques, you can make this task relatively easy and speedy.

When you're ready to start taking off the old window pane by prying out the metal glazing points that are attached to it. These are basically small metal triangles that act as "nails" which hold the window in place within the frame of wood. They are placed under a bead of glazing putty, which is then cured to form a solid, formed wedge that holds the window firmly in place and hides the window's points.

After removing the old pane, clean the frame and wood. Scrape off any old paint and sand the rabbet grooves where the glazing points were placed. Sand them down to bare wooden surfaces so you can paint the frames with the same shade. After the sanding process, apply a coat of flax oil to the wood's surface to help extend its lifespan.

Then, take measurements of the dimensions of the window's opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will also allow for expansion and contraction of the glass during seasonal change. You can take these measurements to a hardware or home improvement store and nearest have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.